/proc/cpuinfo processor : 0 vendor_id : GenuineTMx86 cpu family : 5 model : 4 model name : Transmeta(tm) Crusoe(tm) Processor TM5600 stepping : 3 cpu MHz : 500.000 cache size : 512 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr cx8 cmov mmx longrun constant_tsc cpuid bugs : cpu_meltdown spectre_v1 spectre_v2 spec_store_bypass l1tf mds swapgs itlb_multihit bogomips : 995.47 clflush size : 32 cache_alignment : 32 address sizes : 32 bits physical, 32 bits virtual power management: lspci -[0000:00]-+-00.0 Transmeta Corporation LongRun Northbridge [1279:0395] +-00.1 Transmeta Corporation SDRAM controller [1279:0396] +-00.2 Transmeta Corporation BIOS scratchpad [1279:0397] +-04.0 ULi Electronics Inc. M5451 PCI AC-Link Controller Audio Device [10b9:5451] +-07.0 ULi Electronics Inc. M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+] [10b9:1533] +-09.0 Silicon Motion, Inc. SM712 LynxEM+ [126f:0712] +-0a.0 Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51] +-0a.1 Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51] +-0b.0 Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) [104c:8020] +-0c.0 Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter [10ec:8139] +-0f.0 ULi Electronics Inc. M5229 IDE [10b9:5229] +-11.0 ULi Electronics Inc. M7101 Power Management Controller [PMU] [10b9:7101] \-14.0 ULi Electronics Inc. USB 1.1 Controller [10b9:5237] /proc/meminfo MemTotal: 556104 kB MemFree: 418992 kB MemAvailable: 440548 kB Buffers: 18676 kB Cached: 74264 kB SwapCached: 0 kB Active: 65820 kB Inactive: 40896 kB Active(anon): 14008 kB Inactive(anon): 1664 kB Active(file): 51812 kB Inactive(file): 39232 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 556104 kB LowFree: 418992 kB SwapTotal: 1143804 kB SwapFree: 1143804 kB Dirty: 28 kB Writeback: 0 kB AnonPages: 13804 kB Mapped: 22028 kB Shmem: 1892 kB Slab: 21220 kB SReclaimable: 10860 kB SUnreclaim: 10360 kB KernelStack: 704 kB PageTables: 488 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1421856 kB Committed_AS: 59008 kB VmallocTotal: 446520 kB VmallocUsed: 0 kB VmallocChunk: 0 kB Percpu: 188 kB HardwareCorrupted: 0 kB AnonHugePages: 0 kB ShmemHugePages: 0 kB ShmemPmdMapped: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB Hugetlb: 0 kB DirectMap4k: 65472 kB DirectMap4M: 507904 kB dmidecode # dmidecode 3.2 Getting SMBIOS data from sysfs. SMBIOS 2.3 present. 22 structures occupying 705 bytes. Table at 0x000D8010. Handle 0x0000, DMI type 0, 20 bytes BIOS Information Vendor: CASIO Version: MPC 205/206 Release Date: 10/26/2001 Address: 0xE7E80 Runtime Size: 98688 bytes ROM Size: 256 kB Characteristics: PCI is supported PC Card (PCMCIA) is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) USB legacy is supported Smart battery is supported BIOS boot specification is supported Handle 0x0001, DMI type 1, 25 bytes System Information Manufacturer: CASIO Product Name: FIVA Version: X4.0 Serial Number: 0123456789 UUID: Not Settable Wake-up Type: Power Switch Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: CASIO Product Name: MPC 205/206 Version: X86 Serial Number: TM-200011 Handle 0x0003, DMI type 3, 17 bytes Chassis Information Manufacturer: CASIO Type: Other Lock: Not Present Version: X86 Serial Number: 0 Asset Tag: 0 Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00001234 Handle 0x0004, DMI type 4, 32 bytes Processor Information Socket Designation: CPU Module 1 Type: Central Processor Family: K6-3 Manufacturer: GenuineTMx86 ID: 43 05 00 00 3F 81 80 00 Signature: Family 5, Model 4, Stepping 3 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) CX8 (CMPXCHG8 instruction supported) CMOV (Conditional move instruction supported) MMX (MMX technology supported) Version: Transmeta(tm) Cru Voltage: 3.3 V External Clock: Unknown Max Speed: 450 MHz Current Speed: Unknown Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: Not Provided Handle 0x0005, DMI type 7, 19 bytes Cache Information Socket Designation: L1 Cache Configuration: Enabled, Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 128 kB Maximum Size: 128 kB Supported SRAM Types: Burst Pipeline Burst Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown Handle 0x0006, DMI type 7, 19 bytes Cache Information Socket Designation: L2 Cache Configuration: Enabled, Socketed, Level 2 Operational Mode: Write Back Location: External Installed Size: 0 kB Maximum Size: 256 kB Supported SRAM Types: Burst Pipeline Burst Synchronous Installed SRAM Type: None Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown Handle 0x0007, DMI type 9, 13 bytes System Slot Information Designation: PCI Slot J16 Type: 32-bit PCI Current Usage: Unknown Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided Handle 0x0008, DMI type 9, 13 bytes System Slot Information Designation: PCI Slot J15 Type: 32-bit PCI Current Usage: Unknown Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided Handle 0x0009, DMI type 9, 13 bytes System Slot Information Designation: PCI Slot J14 Type: 32-bit PCI Current Usage: Unknown Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided Handle 0x000A, DMI type 9, 13 bytes System Slot Information Designation: PCI Slot J13 Type: 32-bit PCI Current Usage: Unknown Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided Handle 0x000B, DMI type 9, 13 bytes System Slot Information Designation: PCI Slot J12 Type: 32-bit PCI Current Usage: Unknown Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided Handle 0x000C, DMI type 10, 8 bytes On Board Device 1 Information Type: Video Status: Disabled Description: On Board Device 2 Information Type: Sound Status: Disabled Description: AU8830 Handle 0x000D, DMI type 11, 5 bytes OEM Strings String 1: Transmeta PDB-ALI String 2: Reference Platform Handle 0x000E, DMI type 12, 5 bytes System Configuration Options Option 1: Jumper settings can be described here... Handle 0x000F, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 1 GB Error Information Handle: Not Provided Number Of Devices: 2 Handle 0x0010, DMI type 17, 23 bytes Memory Device Array Handle: 0x000F Error Information Handle: No Error Total Width: 32 bits Data Width: 32 bits Size: 48 MB Form Factor: DIMM Set: 1 Locator: U5 Bank Locator: Bank 0 Type: DRAM Type Detail: Synchronous Speed: Unknown Handle 0x0011, DMI type 17, 23 bytes Memory Device Array Handle: 0x000F Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: U6 Bank Locator: Bank 0 Type: DRAM Type Detail: Unknown Speed: Unknown Handle 0x0012, DMI type 19, 15 bytes Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x00002FFFFFF Range Size: 48 MB Physical Array Handle: 0x000F Partition Width: 2 Handle 0x0013, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x00002FFFFFF Range Size: 48 MB Physical Device Handle: 0x0010 Memory Array Mapped Address Handle: 0x0012 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Handle 0x0014, DMI type 32, 20 bytes System Boot Information Status: Handle 0x0015, DMI type 127, 4 bytes End Of Table dmesg [ 0.000000] Linux version 4.19.0-13-686 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.160-2 (2020-11-28) [ 0.000000] x86/fpu: x87 FPU will use FSAVE [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009b3ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009b400-0x000000000009bfff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e7c00-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000022feffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000022ff0000-0x0000000022fffbff] ACPI data [ 0.000000] BIOS-e820: [mem 0x0000000022fffc00-0x0000000022ffffff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000fff80000-0x00000000ffffffff] reserved [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU! [ 0.000000] SMBIOS 2.3 present. [ 0.000000] DMI: CASIO FIVA/MPC 205/206, BIOS MPC 205/206 10/26/2001 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] last_pfn = 0x22ff0 max_arch_pfn = 0x100000 [ 0.000000] Disabled [ 0.000000] x86/PAT: MTRRs disabled, skipping PAT initialization too. [ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC [ 0.000000] initial memory mapped: [mem 0x00000000-0x17ffffff] [ 0.000000] RAMDISK: [mem 0x211f5000-0x226a6fff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F82A0 000014 (v00 PTLTD ) [ 0.000000] ACPI: RSDT 0x0000000022FFC1E0 00002C (v01 PTLTD RSDT 06040005 LTP 00000000) [ 0.000000] ACPI: FACP 0x0000000022FFFB64 000074 (v01 TMETA PDB.ALI 06040005 PTL 000F4240) [ 0.000000] ACPI: DSDT 0x0000000022FFC20C 003958 (v01 TM PDBALI35 06040005 MSFT 0100000B) [ 0.000000] ACPI: FACS 0x0000000022FFFFC0 000040 [ 0.000000] ACPI: BOOT 0x0000000022FFFBD8 000028 (v01 PTLTD $SBFTBL$ 06040005 LTP 00000001) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 559MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 22ff0000 [ 0.000000] low ram: 0 - 22ff0000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x0000000022feffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009afff] [ 0.000000] node 0: [mem 0x0000000000100000-0x0000000022feffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000022feffff] [ 0.000000] On node 0 totalpages: 143242 [ 0.000000] DMA zone: 40 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3994 pages, LIFO batch:0 [ 0.000000] Normal zone: 1360 pages used for memmap [ 0.000000] Normal zone: 139248 pages, LIFO batch:31 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] No local APIC present or hardware disabled [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009b000-0x0009bfff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009c000-0x000e7fff] [ 0.000000] PM: Registered nosave memory: [mem 0x000e8000-0x000fffff] [ 0.000000] [mem 0x23000000-0xfff7ffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.000000] random: get_random_bytes called from start_kernel+0x81/0x475 with crng_init=0 [ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] percpu: Embedded 29 pages/cpu s87884 r0 d30900 u118784 [ 0.000000] pcpu-alloc: s87884 r0 d30900 u118784 alloc=29*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 141842 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.19.0-13-686 root=UUID=b1650f3f-591e-4547-b8e5-d079fd1fe503 ro vga=771 quiet [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 534044K/572968K available (6651K kernel code, 638K rwdata, 2076K rodata, 844K init, 448K bss, 38924K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] virtual kernel memory layout: fixmap : 0xffd35000 - 0xfffff000 (2856 kB) cpu_entry : 0xff400000 - 0xff8e1000 (4996 kB) pkmap : 0xfec00000 - 0xff000000 (4096 kB) vmalloc : 0xe37f0000 - 0xfebfe000 ( 436 MB) lowmem : 0xc0000000 - 0xe2ff0000 ( 559 MB) .init : 0xd7937000 - 0xd7a0a000 ( 844 kB) .data : 0xd767ed90 - 0xd79278c0 (2722 kB) .text : 0xd7000000 - 0xd767ed90 (6651 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 29359 entries in 58 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=1. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 2304, nr_irqs: 32, preallocated irqs: 16 [ 0.000000] CPU 0 irqstacks, hard=(ptrval) soft=(ptrval) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] ACPI: Core revision 20180810 [ 0.000000] ACPI: setting ELCR to 0200 (from 0e00) [ 0.004000] APIC: Keep in PIC mode(8259) [ 0.012000] tsc: PIT calibration matches PMTIMER. 2 loops [ 0.012000] tsc: Detected 497.738 MHz processor [ 0.004194] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0xe5965723f9, max_idle_ns: 881590479441 ns [ 0.006845] Calibrating delay loop (skipped), value calculated using timer frequency.. 995.47 BogoMIPS (lpj=1990952) [ 0.010548] pid_max: default: 32768 minimum: 301 [ 0.027202] Security Framework initialized [ 0.027707] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.033398] AppArmor: AppArmor initialized [ 0.037603] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.037863] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.134670] CPU: Processor revision 1.3.1.2, 500 MHz [ 0.134718] CPU: Code Morphing Software revision 4.1.7-7-154 [ 0.134744] CPU: 20010606 19:11 official release 18.0.1-4.1.7#3 [ 0.135168] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.135188] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.135222] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.135599] Spectre V2 : Mitigation: Full generic retpoline [ 0.135615] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.135629] Speculative Store Bypass: Vulnerable [ 0.135646] L1TF: Kernel not compiled for PAE. No mitigation for L1TF [ 0.142455] MDS: Vulnerable: Clear CPU buffers attempted, no microcode [ 0.264023] Freeing SMP alternatives memory: 24K [ 0.334836] smpboot: weird, boot CPU (#0) not listed by the BIOS [ 0.337504] smpboot: SMP disabled [ 0.440451] Performance Events: no PMU driver, software events only. [ 0.452621] rcu: Hierarchical SRCU implementation. [ 0.494055] NMI watchdog: Perf NMI watchdog permanently disabled [ 0.512814] smp: Bringing up secondary CPUs ... [ 0.514213] smp: Brought up 1 node, 1 CPU [ 0.514268] smpboot: Max logical packages: 1 [ 0.514330] smpboot: Total of 1 processors activated (995.47 BogoMIPS) [ 0.569447] devtmpfs: initialized [ 0.620329] PM: Registering ACPI NVS region [mem 0x22fffc00-0x22ffffff] (1024 bytes) [ 0.630594] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.630790] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.635132] pinctrl core: initialized pinctrl subsystem [ 0.702204] NET: Registered protocol family 16 [ 0.715101] audit: initializing netlink subsys (disabled) [ 0.733150] audit: type=2000 audit(1610621937.736:1): state=initialized audit_enabled=0 res=1 [ 0.750685] cpuidle: using governor ladder [ 0.751220] cpuidle: using governor menu [ 0.752720] Simple Boot Flag value 0x50 read from CMOS RAM was invalid [ 0.753289] Simple Boot Flag at 0xc set to 0x1 [ 0.753890] clocksource: pit: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1601818034827 ns [ 0.754113] ACPI: bus type PCI registered [ 0.754165] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.792972] PCI: PCI BIOS revision 2.10 entry at 0xfd88e, last bus=0 [ 0.793427] PCI: Using configuration type 1 for base access [ 0.886177] HugeTLB registered 4.00 MiB page size, pre-allocated 0 pages [ 0.923956] ACPI: Added _OSI(Module Device) [ 0.924036] ACPI: Added _OSI(Processor Device) [ 0.924716] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.924766] ACPI: Added _OSI(Processor Aggregator Device) [ 0.924840] ACPI: Added _OSI(Linux-Dell-Video) [ 0.924897] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio) [ 1.012472] random: fast init done [ 1.102272] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 1.209454] ACPI: EC: EC started [ 1.209527] ACPI: EC: interrupt blocked [ 1.213359] ACPI: \_SB_.PCI0.ISA_.EC0_: Used as first EC [ 1.213475] ACPI: \_SB_.PCI0.ISA_.EC0_: GPE=0x8, EC_CMD/EC_SC=0x66, EC_DATA=0x62 [ 1.213545] ACPI: \_SB_.PCI0.ISA_.EC0_: Used as boot DSDT EC to handle transactions [ 1.213565] ACPI: Interpreter enabled [ 1.214843] ACPI: (supports S0 S3 S4 S5) [ 1.214895] ACPI: Using PIC for interrupt routing [ 1.216511] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug [ 1.220329] ACPI: Enabled 2 GPEs in block 00 to 3F [ 1.465706] ACPI: Power Resource [PCR0] (off) [ 1.471912] ACPI: Power Resource [PCR1] (off) [ 1.501144] ACPI: Power Resource [QFAN] (off) [ 1.520887] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 1.521529] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI] [ 1.522077] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 1.522202] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 1.529948] acpi PNP0A03:00: host bridge window [io 0x0cf8-0x0cff] (ignored) [ 1.530088] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7 window] (ignored) [ 1.530176] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff window] (ignored) [ 1.530445] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff window] (ignored) [ 1.530542] acpi PNP0A03:00: host bridge window [mem 0x000cc000-0x000dbfff window] (ignored) [ 1.531489] acpi PNP0A03:00: host bridge window [mem 0x000dc000-0x000fffff window] (ignored) [ 1.531578] acpi PNP0A03:00: host bridge window [mem 0xfff80000-0xffffffff window] (ignored) [ 1.531943] acpi PNP0A03:00: host bridge window [mem 0x230e0000-0xffdfffff window] (ignored) [ 1.531983] PCI: root bus 00: using default resources [ 1.536923] PCI host bridge to bus 0000:00 [ 1.537086] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.537407] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff] [ 1.537519] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.541313] pci 0000:00:00.0: [1279:0395] type 00 class 0x060000 [ 1.542333] pci 0000:00:00.0: reg 0x10: [mem 0xfc100000-0xfc1fffff] [ 1.547290] pci 0000:00:00.1: [1279:0396] type 00 class 0x050000 [ 1.555094] pci 0000:00:00.2: [1279:0397] type 00 class 0x050000 [ 1.562474] pci 0000:00:04.0: [10b9:5451] type 00 class 0x040100 [ 1.563234] pci 0000:00:04.0: reg 0x10: [io 0x1000-0x10ff] [ 1.564329] pci 0000:00:04.0: reg 0x14: [mem 0xfc004000-0xfc004fff] [ 1.565960] pci 0000:00:04.0: supports D1 D2 [ 1.566122] pci 0000:00:04.0: PME# supported from D2 D3hot D3cold [ 1.571389] pci 0000:00:07.0: [10b9:1533] type 00 class 0x060100 [ 1.577245] pci 0000:00:09.0: [126f:0712] type 00 class 0x030000 [ 1.578240] pci 0000:00:09.0: reg 0x10: [mem 0xfd000000-0xfdffffff] [ 1.580111] pci 0000:00:09.0: supports D1 D2 [ 1.583274] pci 0000:00:0a.0: [104c:ac51] type 02 class 0x060700 [ 1.583768] pci 0000:00:0a.0: reg 0x10: [mem 0x24000000-0x24000fff] [ 1.584131] pci 0000:00:0a.0: supports D1 D2 [ 1.584168] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.587747] pci 0000:00:0a.1: [104c:ac51] type 02 class 0x060700 [ 1.588889] pci 0000:00:0a.1: reg 0x10: [mem 0x30000000-0x30000fff] [ 1.590019] pci 0000:00:0a.1: supports D1 D2 [ 1.590063] pci 0000:00:0a.1: PME# supported from D0 D1 D2 D3hot D3cold [ 1.595603] pci 0000:00:0b.0: [104c:8020] type 00 class 0x0c0010 [ 1.596214] pci 0000:00:0b.0: reg 0x10: [mem 0xfc006000-0xfc0067ff] [ 1.596494] pci 0000:00:0b.0: reg 0x14: [mem 0xfc000000-0xfc003fff] [ 1.596903] pci 0000:00:0b.0: supports D2 [ 1.596939] pci 0000:00:0b.0: PME# supported from D2 D3hot [ 1.598503] pci 0000:00:0c.0: [10ec:8139] type 00 class 0x020000 [ 1.598848] pci 0000:00:0c.0: reg 0x10: [io 0x1400-0x14ff] [ 1.598944] pci 0000:00:0c.0: reg 0x14: [mem 0xfc006800-0xfc0068ff] [ 1.599632] pci 0000:00:0c.0: supports D1 D2 [ 1.599673] pci 0000:00:0c.0: PME# supported from D1 D2 D3hot [ 1.602679] pci 0000:00:0f.0: [10b9:5229] type 00 class 0x01018e [ 1.602865] pci 0000:00:0f.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size) [ 1.602918] pci 0000:00:0f.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.603020] pci 0000:00:0f.0: reg 0x18: [io 0x0000-0x0007] [ 1.603106] pci 0000:00:0f.0: reg 0x1c: [io 0x0000-0x0003] [ 1.603465] pci 0000:00:0f.0: reg 0x20: [io 0x1800-0x180f] [ 1.603581] pci 0000:00:0f.0: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.604465] pci 0000:00:0f.0: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.606033] pci 0000:00:11.0: [10b9:7101] type 00 class 0x068000 [ 1.606420] pci 0000:00:11.0: quirk: [io 0x8000-0x803f] claimed by ali7101 ACPI [ 1.606508] pci 0000:00:11.0: quirk: [io 0x8040-0x805f] claimed by ali7101 SMB [ 1.609056] pci 0000:00:14.0: [10b9:5237] type 00 class 0x0c0310 [ 1.610021] pci 0000:00:14.0: reg 0x10: [mem 0x000d0000-0x000d0fff] [ 1.613749] pci 0000:00:0a.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.613876] pci 0000:00:0a.1: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.614610] pci_bus 0000:01: extended config space not accessible [ 1.615306] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 04 [ 1.616038] pci_bus 0000:05: extended config space not accessible [ 1.618659] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 08 [ 1.618767] pci_bus 0000:00: on NUMA node 0 [ 1.633143] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 10 11) *9 [ 1.637049] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 7 10 11) [ 1.639194] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 *4 5 7 10 11) [ 1.642268] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 *10 11) [ 1.644186] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 10 *11) [ 1.648658] ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 7 10 11) *0, disabled. [ 1.651219] ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 7 10 11) *0, disabled. [ 1.654338] ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 7 *10 11) [ 1.656101] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 10 *11) [ 1.695794] ACPI: EC: interrupt unblocked [ 1.695957] ACPI: EC: event unblocked [ 1.699751] ACPI: \_SB_.PCI0.ISA_.EC0_: GPE=0x8, EC_CMD/EC_SC=0x66, EC_DATA=0x62 [ 1.699837] ACPI: \_SB_.PCI0.ISA_.EC0_: Used as boot DSDT EC to handle transactions and events [ 1.709792] pci 0000:00:09.0: vgaarb: setting as boot VGA device [ 1.709883] pci 0000:00:09.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 1.712881] pci 0000:00:09.0: vgaarb: bridge control possible [ 1.713135] vgaarb: loaded [ 1.723382] EDAC MC: Ver: 3.0.0 [ 1.739371] PCI: Using ACPI for IRQ routing [ 1.739841] PCI: pci_cache_line_size set to 32 bytes [ 1.744877] e820: reserve RAM buffer [mem 0x0009b400-0x0009ffff] [ 1.745117] e820: reserve RAM buffer [mem 0x22ff0000-0x23ffffff] [ 1.765597] clocksource: Switched to clocksource tsc-early [ 1.964194] VFS: Disk quotas dquot_6.6.0 [ 1.965321] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.976244] AppArmor: AppArmor Filesystem Enabled [ 1.978357] pnp: PnP ACPI init [ 1.981343] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.984995] pnp 00:01: Plug and Play ACPI device, IDs PNP0320 (active) [ 1.986791] pnp 00:02: Plug and Play ACPI device, IDs IBM3780 PNP0f13 (active) [ 1.998720] system 00:03: [io 0x0170-0x0176] has been reserved [ 1.999221] system 00:03: [io 0x0376] has been reserved [ 1.999817] system 00:03: [io 0x04d0-0x04d1] has been reserved [ 1.999884] system 00:03: [io 0x040b] has been reserved [ 2.000003] system 00:03: [io 0x0480-0x048f] has been reserved [ 2.000054] system 00:03: [io 0x04d6] has been reserved [ 2.000113] system 00:03: [io 0x8000-0x803f] has been reserved [ 2.000163] system 00:03: [io 0x8040-0x805f] has been reserved [ 2.000415] system 00:03: [mem 0xfff80000-0xffffffff] has been reserved [ 2.000914] system 00:03: [mem 0x23000000-0x23ffffff] could not be reserved [ 2.001173] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active) [ 2.034908] pnp: PnP ACPI: found 4 devices [ 2.034997] PnPBIOS: Disabled [ 2.196669] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 2.201000] pci 0000:00:0a.0: BAR 15: assigned [mem 0x28000000-0x2bffffff pref] [ 2.201775] pci 0000:00:0a.0: BAR 16: assigned [mem 0x2c000000-0x2fffffff] [ 2.203242] pci 0000:00:0a.1: BAR 15: assigned [mem 0x34000000-0x37ffffff pref] [ 2.205483] pci 0000:00:0a.1: BAR 16: assigned [mem 0x38000000-0x3bffffff] [ 2.206594] pci 0000:00:0a.0: BAR 13: assigned [io 0x1c00-0x1cff] [ 2.206693] pci 0000:00:0a.0: BAR 14: assigned [io 0x2000-0x20ff] [ 2.206778] pci 0000:00:0a.1: BAR 13: assigned [io 0x2400-0x24ff] [ 2.206861] pci 0000:00:0a.1: BAR 14: assigned [io 0x2800-0x28ff] [ 2.206943] pci 0000:00:0f.0: BAR 2: assigned [io 0x1810-0x1817] [ 2.207071] pci 0000:00:0f.0: BAR 3: assigned [io 0x1818-0x181b] [ 2.208421] pci 0000:00:0a.0: CardBus bridge to [bus 01-04] [ 2.208462] pci 0000:00:0a.0: bridge window [io 0x1c00-0x1cff] [ 2.208504] pci 0000:00:0a.0: bridge window [io 0x2000-0x20ff] [ 2.208544] pci 0000:00:0a.0: bridge window [mem 0x28000000-0x2bffffff pref] [ 2.208584] pci 0000:00:0a.0: bridge window [mem 0x2c000000-0x2fffffff] [ 2.208638] pci 0000:00:0a.1: CardBus bridge to [bus 05-08] [ 2.208663] pci 0000:00:0a.1: bridge window [io 0x2400-0x24ff] [ 2.208693] pci 0000:00:0a.1: bridge window [io 0x2800-0x28ff] [ 2.208727] pci 0000:00:0a.1: bridge window [mem 0x34000000-0x37ffffff pref] [ 2.208762] pci 0000:00:0a.1: bridge window [mem 0x38000000-0x3bffffff] [ 2.208846] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 2.208884] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff] [ 2.208921] pci_bus 0000:01: resource 0 [io 0x1c00-0x1cff] [ 2.208946] pci_bus 0000:01: resource 1 [io 0x2000-0x20ff] [ 2.208974] pci_bus 0000:01: resource 2 [mem 0x28000000-0x2bffffff pref] [ 2.208997] pci_bus 0000:01: resource 3 [mem 0x2c000000-0x2fffffff] [ 2.209028] pci_bus 0000:05: resource 0 [io 0x2400-0x24ff] [ 2.209053] pci_bus 0000:05: resource 1 [io 0x2800-0x28ff] [ 2.209453] pci_bus 0000:05: resource 2 [mem 0x34000000-0x37ffffff pref] [ 2.209484] pci_bus 0000:05: resource 3 [mem 0x38000000-0x3bffffff] [ 2.211697] NET: Registered protocol family 2 [ 2.225054] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 2.225597] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 2.226671] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 2.227591] TCP: Hash tables configured (established 8192 bind 8192) [ 2.234340] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 2.235413] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 2.241235] NET: Registered protocol family 1 [ 2.241827] NET: Registered protocol family 44 [ 2.242115] pci 0000:00:07.0: Activating ISA DMA hang workarounds [ 2.242477] pci 0000:00:09.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 2.248732] PCI Interrupt Link [LNKU] enabled at IRQ 11 [ 2.248805] PCI: setting IRQ 11 as level-triggered [ 2.315828] pci 0000:00:14.0: quirk_usb_early_handoff+0x0/0x6d7 took 71034 usecs [ 2.315943] PCI: CLS 32 bytes, default 32 [ 2.338374] Unpacking initramfs... [ 6.064915] Freeing initrd memory: 21192K [ 6.080569] Initialise system trusted keyrings [ 6.081585] Key type blacklist registered [ 6.082833] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 6.107400] zbud: loaded [ 7.093020] tsc: Refined TSC clocksource calibration: 497.745 MHz [ 7.093304] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe5972aac58, max_idle_ns: 881590472028 ns [ 7.093767] clocksource: Switched to clocksource tsc [ 18.100878] Key type asymmetric registered [ 18.100947] Asymmetric key parser 'x509' registered [ 18.101265] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 18.103973] io scheduler noop registered [ 18.104042] io scheduler deadline registered [ 18.105324] io scheduler cfq registered (default) [ 18.105396] io scheduler mq-deadline registered [ 18.120319] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 18.123486] vesafb: mode is 800x600x8, linelength=800, pages=0 [ 18.123526] vesafb: scrolling: redraw [ 18.123561] vesafb: Pseudocolor: size=0:8:8:8, shift=0:0:0:0 [ 18.124914] vesafb: framebuffer at 0xfd000000, mapped to 0x(ptrval), using 512k, total 512k [ 18.179331] Console: switching to colour frame buffer device 100x37 [ 18.207553] fb0: VESA VGA frame buffer device [ 18.209088] tsc: Marking TSC unstable due to TSC halts in idle [ 18.213717] clocksource: Switched to clocksource acpi_pm [ 18.215529] isapnp: Scanning for PnP cards... [ 18.533154] isapnp: No Plug & Play device found [ 18.539695] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 18.555930] Linux agpgart interface v0.103 [ 18.562923] i8042: PNP: PS/2 Controller [PNP0320:KBC1,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 18.573758] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 18.573954] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 18.577469] mousedev: PS/2 mouse device common for all mice [ 18.583998] rtc_cmos 00:00: RTC can wake from S4 [ 18.588349] rtc_cmos 00:00: registered as rtc0 [ 18.589002] rtc_cmos 00:00: alarms up to one month, y3k, 114 bytes nvram [ 18.591302] ledtrig-cpu: registered to indicate activity on CPUs [ 18.606706] NET: Registered protocol family 10 [ 18.626819] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 19.477897] Segment Routing with IPv6 [ 19.478293] mip6: Mobile IPv6 [ 19.478371] NET: Registered protocol family 17 [ 19.480100] mpls_gso: MPLS GSO support [ 19.480196] mce: Unable to init MCE device (rc: -5) [ 19.483647] mce: Using 0 MCE banks [ 19.484154] Using IPI No-Shortcut mode [ 19.488047] registered taskstats version 1 [ 19.488095] Loading compiled-in X.509 certificates [ 22.133683] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 22.136235] Loaded X.509 cert 'Debian Secure Boot Signer 2020: 00b55eb3b9' [ 22.137670] zswap: loaded using pool lzo/zbud [ 22.139166] AppArmor: AppArmor sha1 policy hashing enabled [ 22.150993] rtc_cmos 00:00: setting system clock to 2021-01-14 10:59:20 UTC (1610621960) [ 22.151453] Unstable clock detected, switching default tracing clock to "global" If you want to keep using the local clock, then add: "trace_clock=local" on the kernel command line [ 22.175667] Freeing unused kernel image memory: 844K [ 22.187777] Write protecting the kernel text: 6652k [ 22.189755] Write protecting the kernel read-only data: 2084k [ 22.189808] Run /init as init process [ 27.147719] ali1535_smbus 0000:00:11.0: enabling device (0000 -> 0001) [ 27.180894] ACPI Warning: SystemIO range 0x0000000000008040-0x000000000000805F conflicts with OpRegion 0x0000000000008000-0x000000000000804F (\_SB.PCI0.ISA.GLBL) (20180810/utaddress-213) [ 27.181135] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 27.181185] ali1535_smbus 0000:00:11.0: ALI1535 not detected, module not inserted. [ 27.182710] thermal LNXTHERM:00: registered as thermal_zone0 [ 27.182759] ACPI: Thermal Zone [THRM] (54 C) [ 27.555504] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 27.555601] 8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too [ 27.605911] ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr [ 27.607213] ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted. [ 27.883270] SCSI subsystem initialized [ 28.158883] PCI Interrupt Link [LNK4] enabled at IRQ 10 [ 28.158966] PCI: setting IRQ 10 as level-triggered [ 28.174022] ACPI: bus type USB registered [ 28.174499] usbcore: registered new interface driver usbfs [ 28.174733] usbcore: registered new interface driver hub [ 28.182109] usbcore: registered new device driver usb [ 28.247253] 8139too: 8139too Fast Ethernet driver 0.9.28 [ 28.302336] firewire_ohci 0000:00:0b.0: added OHCI v1.0 device as card 0, 4 IR + 8 IT contexts, quirks 0x2 [ 28.337372] PCI Interrupt Link [LNK5] enabled at IRQ 11 [ 28.401325] 8139too 0000:00:0c.0 eth0: RealTek RTL8139 at 0x(ptrval), 08:00:74:50:0f:0b, IRQ 11 [ 28.560148] psmouse serio1: hgpk: ID: 10 00 64 [ 28.569468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 28.673597] libata version 3.00 loaded. [ 28.782443] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 28.827859] pata_ali 0000:00:0f.0: can't derive routing for PCI INT A [ 28.828740] pata_ali 0000:00:0f.0: PCI INT A: not connected [ 28.921301] firewire_core 0000:00:0b.0: created device fw0: GUID 0800740300500f0b, S400 [ 28.928142] psmouse serio1: trackpoint: IBM TrackPoint firmware: 0x0b, buttons: 3/3 [ 28.944047] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input2 [ 28.981938] ehci-pci: EHCI PCI platform driver [ 29.004967] scsi host0: pata_ali [ 29.026077] scsi host1: pata_ali [ 29.028361] ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0x1800 irq 14 [ 29.028785] ata2: PATA max UDMA/66 cmd 0x1810 ctl 0x1818 bmdma 0x1808 irq 15 [ 29.099997] ohci-pci: OHCI PCI platform driver [ 29.114983] ohci-pci 0000:00:14.0: OHCI PCI host controller [ 29.115283] ohci-pci 0000:00:14.0: new USB bus registered, assigned bus number 1 [ 29.115969] ohci-pci 0000:00:14.0: irq 11, io mem 0x000d0000 [ 29.193424] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 29.193495] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 29.193522] usb usb1: Product: OHCI PCI host controller [ 29.193549] usb usb1: Manufacturer: Linux 4.19.0-13-686 ohci_hcd [ 29.193575] usb usb1: SerialNumber: 0000:00:14.0 [ 29.210388] hub 1-0:1.0: USB hub found [ 29.228211] ata1.00: ATA-6: FUJITSU MHT2040AS, 006C, max UDMA/100 [ 29.228280] ata1.00: 78140160 sectors, multi 16: LBA [ 29.230942] hub 1-0:1.0: 2 ports detected [ 29.298811] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2040A 006C PQ: 0 ANSI: 5 [ 29.674261] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.3 GiB) [ 29.678715] sd 0:0:0:0: [sda] Write Protect is off [ 29.678808] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 29.692628] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 29.847957] sda: sda1 sda2 < sda5 sda6 > [ 29.877235] sd 0:0:0:0: [sda] Attached SCSI disk [ 30.991704] random: crng init done [ 32.474591] PM: Image not found (code -22) [ 34.252856] cryptd: max_cpu_qlen set to 1000 [ 35.049342] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 40.398991] systemd[1]: Inserted module 'autofs4' [ 41.247399] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 41.257057] systemd[1]: Detected architecture x86. [ 41.466573] systemd[1]: Set hostname to . [ 48.937290] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 49.308315] systemd[1]: Listening on RPCbind Server Activation Socket. [ 49.343273] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 49.349955] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 49.362237] systemd[1]: Listening on fsck to fsckd communication Socket. [ 49.389381] systemd[1]: Listening on Journal Audit Socket. [ 49.402763] systemd[1]: Created slice system-getty.slice. [ 49.414174] systemd[1]: Listening on udev Kernel Socket. [ 49.431859] systemd[1]: Listening on Journal Socket. [ 49.502337] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 51.123893] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 51.406524] RPC: Registered named UNIX socket transport module. [ 51.406591] RPC: Registered udp transport module. [ 51.406611] RPC: Registered tcp transport module. [ 51.406631] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 52.844871] lp: driver loaded but no devices found [ 53.802885] ppdev: user-space parallel port driver [ 54.651876] systemd[1]: Started Load/Save Random Seed. [ 54.955534] loop: module loaded [ 55.113347] systemd[1]: Started Load Kernel Modules. [ 55.186086] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 55.313845] systemd[1]: Starting Apply Kernel Variables... [ 55.337278] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. [ 55.805303] systemd[1]: Started Create System Users. [ 55.992977] systemd[1]: Starting Create Static Device Nodes in /dev... [ 56.117432] systemd[1]: Started Apply Kernel Variables. [ 57.593520] systemd[1]: Started Create Static Device Nodes in /dev. [ 57.782381] systemd[1]: Starting udev Kernel Device Manager... [ 60.087978] systemd[1]: Started Journal Service. [ 62.080931] systemd-journald[186]: Received request to flush runtime journal from PID 1 [ 64.059619] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3 [ 64.060049] ACPI: Power Button [PWRB] [ 64.102672] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4 [ 64.103964] ACPI: Sleep Button [SLPB] [ 64.126358] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input5 [ 64.176975] ACPI: Lid Switch [LID] [ 64.178672] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6 [ 64.208804] ACPI: Power Button [PWRF] [ 64.230934] ACPI: AC Adapter [ACAD] (on-line) [ 64.703989] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 64.761768] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input7 [ 65.657641] alim1535_wdt: initialized. timeout=60 sec (nowayout=0) [ 65.858949] battery: ACPI: Battery Slot [BAT1] (battery present) [ 65.990330] alim7101_wdt: Steve Hill [ 65.991090] alim7101_wdt: Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter. [ 66.031046] alim7101_wdt: Steve Hill [ 66.031227] alim7101_wdt: Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter. [ 66.456360] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 66.542164] PCI Interrupt Link [LNK2] enabled at IRQ 5 [ 66.542284] PCI: setting IRQ 5 as level-triggered [ 66.542755] yenta_cardbus 0000:00:0a.0: CardBus bridge found [1265:0300] [ 66.542925] yenta_cardbus 0000:00:0a.0: Enabling burst memory read transactions [ 66.542967] yenta_cardbus 0000:00:0a.0: Using CSCINT to route CSC interrupts to PCI [ 66.542993] yenta_cardbus 0000:00:0a.0: Routing CardBus interrupts to PCI [ 66.543030] yenta_cardbus 0000:00:0a.0: TI: mfunc 0x012c1222, devctl 0x66 [ 66.787158] yenta_cardbus 0000:00:0a.0: ISA IRQ mask 0x00d8, PCI irq 5 [ 66.787693] yenta_cardbus 0000:00:0a.0: Socket status: 30000006 [ 66.843291] PCI Interrupt Link [LNK3] enabled at IRQ 4 [ 66.843406] PCI: setting IRQ 4 as level-triggered [ 66.843983] yenta_cardbus 0000:00:0a.1: CardBus bridge found [1265:0300] [ 66.844165] yenta_cardbus 0000:00:0a.1: Using CSCINT to route CSC interrupts to PCI [ 66.844189] yenta_cardbus 0000:00:0a.1: Routing CardBus interrupts to PCI [ 66.844226] yenta_cardbus 0000:00:0a.1: TI: mfunc 0x012c1222, devctl 0x66 [ 66.967327] input: PC Speaker as /devices/platform/pcspkr/input/input8 [ 67.138367] yenta_cardbus 0000:00:0a.1: ISA IRQ mask 0x00c8, PCI irq 4 [ 67.138465] yenta_cardbus 0000:00:0a.1: Socket status: 30000006 [ 68.960046] PCI Interrupt Link [LNK8] enabled at IRQ 10 [ 72.590985] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: [ 72.611555] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: [ 72.664180] excluding [ 72.682688] excluding 0x170-0x177 0x1f0-0x1f7 0x200-0x207 0x220-0x22f [ 72.692925] 0x170-0x177 0x1f0-0x1f7 0x200-0x207 0x220-0x22f 0x330-0x337 0x370-0x377 0x388-0x38f [ 72.713328] 0x330-0x337 [ 72.721516] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: [ 72.722949] excluding 0x3f0-0x3f7 0x408-0x40f 0x480-0x48f [ 72.725553] 0x370-0x377 0x388-0x38f [ 72.753808] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: [ 72.754730] excluding 0x3f0-0x3f7 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 [ 72.765003] 0x4d0-0x4d7 [ 72.766044] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: [ 72.773962] clean [ 72.774787] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: [ 72.776012] clean [ 72.789332] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: [ 72.790501] clean [ 72.823408] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: [ 72.826135] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff: [ 72.826333] excluding 0xc0000-0xcbfff 0xd0000-0xd3fff [ 72.855950] clean [ 72.869125] 0xe4000-0xfffff [ 72.871486] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff: [ 72.901294] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: [ 72.901479] excluding 0xc0000-0xcbfff 0xd0000-0xd3fff 0xe4000-0xfffff [ 72.903539] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: [ 72.903709] clean [ 72.904077] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: [ 72.904209] clean [ 72.932971] clean [ 72.936018] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff: [ 72.936226] clean [ 72.983877] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: [ 72.985406] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: [ 72.986671] clean [ 73.017769] clean [ 77.998541] Adding 1143804k swap on /dev/sda5. Priority:-2 extents:1 across:1143804k FS [ 79.965347] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 84.126849] audit: type=1400 audit(1610622022.471:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=329 comm="apparmor_parser" [ 84.127034] audit: type=1400 audit(1610622022.471:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=329 comm="apparmor_parser" [ 84.975697] audit: type=1400 audit(1610622023.315:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=335 comm="apparmor_parser" [ 84.980998] audit: type=1400 audit(1610622023.319:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=335 comm="apparmor_parser" [ 84.981187] audit: type=1400 audit(1610622023.319:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=335 comm="apparmor_parser" [ 85.467460] audit: type=1400 audit(1610622023.811:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=336 comm="apparmor_parser" [ 86.117479] audit: type=1400 audit(1610622024.459:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=338 comm="apparmor_parser" [ 86.117663] audit: type=1400 audit(1610622024.459:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=338 comm="apparmor_parser" [ 86.117814] audit: type=1400 audit(1610622024.459:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd//third_party" pid=338 comm="apparmor_parser" [ 94.335287] 8139too 0000:00:0c.0 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1