cpu			: Alpha
cpu model		: PCA56
cpu variation		: 7
cpu revision		: 0
cpu serial number	: 
system type		: EB164
system variation	: SX164
system revision		: 0
system serial number	: 
cycle frequency [Hz]	: 533333333 
timer frequency [Hz]	: 1024.00
page size [bytes]	: 8192
phys. address bits	: 40
max. addr. space #	: 127
BogoMIPS		: 1053.12
kernel unaligned acc	: 0 (pc=0,va=0)
user unaligned acc	: 0 (pc=0,va=0)
platform string		: Digital AlphaPC 164SX 533 MHz
cpus detected		: 1
L1 Icache		: 16K, 1-way, 64b line
L1 Dcache		: 8K, 1-way, 32b line
L2 cache		: 1024K, 1-way, 64b line
L3 cache		: n/a
00:05.0 Ethernet controller [0200]: Digital Equipment Corporation DECchip 21142/43 [1011:0019] (rev 30)
	Subsystem: Digital Equipment Corporation DE500B Fast Ethernet [1011:500b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (5000ns min, 10000ns max)
	Interrupt: pin A routed to IRQ 25
	Region 0: I/O ports at 8000 [size=128]
	Region 1: Memory at 0a865000 (32-bit, non-prefetchable) [size=128]
	Expansion ROM at 0a800000 [disabled] [size=256K]
	Kernel driver in use: tulip
	Kernel modules: tulip

00:08.0 ISA bridge [0601]: Contaq Microsystems 82c693 [1080:c693]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel modules: cy82c693

00:08.1 IDE interface [0101]: Contaq Microsystems 82c693 [1080:c693] (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 0
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 4: I/O ports at 8080 [size=16]
	Kernel driver in use: Cypress_IDE
	Kernel modules: ata_generic, ide-pci-generic, cy82c693

00:08.2 IDE interface [0101]: Contaq Microsystems 82c693 [1080:c693] (prog-if 00 [])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 0
	Region 0: I/O ports at 0170 [size=8]
	Region 1: I/O ports at 0374 [size=1]
	Region 4: Memory at 0a840000 (32-bit, non-prefetchable) [disabled] [size=64K]
	Kernel modules: ata_generic, ide-pci-generic, cy82c693

00:08.3 USB Controller [0c03]: Contaq Microsystems 82c693 [1080:c693] (prog-if 10 [OHCI])
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 0
	Region 0: Memory at 0a864000 (32-bit, non-prefetchable) [size=4K]
	Kernel modules: ohci-hcd, cy82c693

00:09.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA 2164W [Millennium II] [102b:051b] (prog-if 00 [VGA controller])
	Subsystem: Matrox Graphics, Inc. Device [102b:0200]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 24
	Region 0: Memory at 09000000 (32-bit, prefetchable) [size=16M]
	Region 1: Memory at 0a860000 (32-bit, non-prefetchable) [size=16K]
	Region 2: Memory at 0a000000 (32-bit, non-prefetchable) [size=8M]
	Expansion ROM at 0a850000 [disabled] [size=64K]
	Kernel modules: matroxfb_base

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-2-alpha-generic (Debian 2.6.26-29) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Sun Mar 4 21:08:03 UTC 2012
[    0.000000] Booting GENERIC on EB164 variation SX164 using machine vector SX164 from SRM
[    0.000000] Major Options: MAGIC_SYSRQ 
[    0.000000] Command line: ro  root=/dev/hda3
[    0.000000] memcluster 0, usage 1, start        0, end      256
[    0.000000] memcluster 1, usage 0, start      256, end    65527
[    0.000000] memcluster 2, usage 1, start    65527, end    65536
[    0.000000] freeing pages 256:2048
[    0.000000] freeing pages 2987:65527
[    0.000000] reserving pages 2987:2988
[    0.000000] Initial ramdisk at: 0xfffffc001f61a000 (9244883 bytes)
[    0.000000] 1024K Bcache detected; load hit latency 24 cycles, load miss latency 105 cycles
[    0.000000] PCA56 MVI set enabled
[    0.000000] pci: cia revision 1 (pyxis)
[    0.000000] On node 0 totalpages: 65527
[    0.000000]   DMA zone: 448 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 65079 pages, LIFO batch:15
[    0.000000]   Normal zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65079
[    0.000000] Kernel command line: ro  root=/dev/hda3
[    0.000000] PID hash table entries: 2048 (order: 11, 16384 bytes)
[    0.000000] Using epoch = 2000
[4194001.855599] Console: colour VGA+ 80x25
[4194001.855599] console [tty0] enabled
[4194001.858529] Dentry cache hash table entries: 65536 (order: 6, 524288 bytes)
[4194001.861459] Inode-cache hash table entries: 32768 (order: 5, 262144 bytes)
[4194001.919076] Memory: 500584k/524216k available (2162k kernel code, 20952k reserved, 3314k data, 304k init)
[4194001.920052] Calibrating delay loop... 1053.12 BogoMIPS (lpj=514048)
[4194001.937630] Security Framework initialized
[4194001.937630] Capability LSM initialized
[4194001.937630] Mount-cache hash table entries: 512
[4194001.938607] Initializing cgroup subsys ns
[4194001.938607] Initializing cgroup subsys cpuacct
[4194001.938607] Initializing cgroup subsys devices
[4194001.949349] net_namespace: 1208 bytes
[4194001.950326] NET: Registered protocol family 16
[4194001.953255] EISA bus registered
[4194001.954232] pci: passed tb register update test
[4194001.954232] pci: passed sg loopback i/o read test
[4194001.954232] pci: passed pte write cache snoop test
[4194001.954232] pci: failed valid tag invalid pte reload test (mcheck; workaround available)
[4194001.954232] pci: passed pci machine check test
[4194001.954232] pci: tbia workaround enabled
[4194001.955208] pci: enabling save/restore of SRM state
[4194001.959115] SMC37c669 Super I/O Controller found @ 0x3f0
[4194001.964974] Linux Plug and Play Support v0.97 (c) Adam Belay
[4194001.976693] NET: Registered protocol family 2
[4194001.985482] IP route cache hash table entries: 4096 (order: 2, 32768 bytes)
[4194001.986458] TCP established hash table entries: 16384 (order: 5, 262144 bytes)
[4194001.987435] TCP bind hash table entries: 16384 (order: 4, 131072 bytes)
[4194001.988412] TCP: Hash tables configured (established 16384 bind 16384)
[4194001.988412] TCP reno registered
[4194001.991341] NET: Registered protocol family 1
[4194001.992318] checking if image is initramfs... it is
[4194008.181768] Freeing initrd memory: 9028k freed
[4194008.185674] VFS: Disk quotas dquot_6.5.1
[4194008.185674] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
[4194008.185674] msgmni has been set to 996
[4194008.187627] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[4194008.188604] io scheduler noop registered
[4194008.188604] io scheduler anticipatory registered
[4194008.188604] io scheduler deadline registered
[4194008.188604] io scheduler cfq registered (default)
[4194008.188604] isapnp: Scanning for PnP cards...
[4194008.541143] isapnp: No Plug & Play device found
[4194008.564580] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[4194008.565557] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4194008.565557] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4194008.580205] brd: module loaded
[4194008.586064] serio: i8042 KBD port at 0x60,0x64 irq 1
[4194008.586064] serio: i8042 AUX port at 0x60,0x64 irq 12
[4194008.588018] mice: PS/2 mouse device common for all mice
[4194008.588994] EISA: Probing bus 0 at eisa.0
[4194008.591924] TCP cubic registered
[4194008.591924] NET: Registered protocol family 17
[4194008.592900] registered taskstats version 1
[4194008.593877] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[4194008.593877] Freeing unused kernel memory: 304k freed
[4194009.094853] input: AT Raw Set 2 keyboard as /class/input/input0
[4194009.116338] atkbd.c: keyboard reset failed on isa0060/serio1
[4194025.339962] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
[4194025.340939] PCI: Setting latency timer of device 0000:00:05.0 to 64
[4194025.344845] tulip0:  EEPROM default media type Autosense.
[4194025.344845] tulip0:  Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
[4194025.344845] tulip0:  Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2) block.
[4194025.344845] tulip0:  Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
[4194025.344845] tulip0:  Index #3 - Media 100baseTx-FDX (#5) described by a 21143 SYM PHY (4) block.
[4194025.350704] eth0: Digital DS21142/43 Tulip rev 48 at Port 0x8000, xx:xx:xx:xx:xx:xx, IRQ 25.
[4194025.650509] Uniform Multi-Platform E-IDE driver
[4194025.651485] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4194025.725704] CY82C693: IDE controller (0x1080:0xc693 rev 0x00) at  PCI slot 0000:00:08.1
[4194025.725704] CY82C693: not 100% native mode: will probe irqs later
[4194025.725704] CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)
[4194025.725704] pci 0000:00:08.2: enabling device (0005 -> 0007)
[4194025.725704]     ide0: BM-DMA at 0x8080-0x8087
[4194025.725704]     ide1: BM-DMA at 0x8088-0x808f
[4194025.725704] Probing IDE interface ide0...
[4194025.966915] SCSI subsystem initialized
[4194026.384883] hda: FUJITSU MPF3204AT, ATA DISK drive
[4194026.417110] libata version 3.00 loaded.
[4194026.590938] usbcore: registered new interface driver usbfs
[4194026.591915] usbcore: registered new interface driver hub
[4194026.591915] usbcore: registered new device driver usb
[4194026.598751] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[4194027.713008] hdb: CD-540E, ATAPI CD/DVD-ROM drive
[4194027.819453] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[4194027.819453] hda: MWDMA2 mode selected
[4194027.820430] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[4194027.820430] hdb: MWDMA2 mode selected
[4194027.820430] Probing IDE interface ide1...
[4194028.871210] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4194028.871210] ide1 at 0x170-0x177,0x376 on irq 15
[4194028.874140] ohci_hcd 0000:00:08.3: Found HC with no IRQ.  Check BIOS/PCI 0000:00:08.3 setup!
[4194028.875117] ohci_hcd 0000:00:08.3: init 0000:00:08.3 fail, -19
[4194030.574334] hda: max request size: 128KiB
[4194030.591913] hda: 40031712 sectors (20496 MB) w/512KiB Cache, CHS=39714/16/63
[4194030.591913] hda: cache flushes not supported
[4194030.591913]  hda: hda1 hda2 hda3 hda4
[4194030.773553] hdb: ATAPI 40X CD-ROM drive, 128kB Cache
[4194030.773553] Uniform CD-ROM driver Revision: 3.20
[4194033.590934] kjournald starting.  Commit interval 5 seconds
[4194033.590934] EXT3-fs: mounted filesystem with ordered data mode.
[4194037.643667] udevd version 125 started
[4194064.693458] input: PC Speaker as /class/input/input1
[4194068.511815] Adding 739464k swap on /dev/hda4.  Priority:-1 extents:1 across:739464k
[4194069.356541] EXT3 FS on hda3, internal journal
[4194071.131931] loop: module loaded
[4194096.215902] NET: Registered protocol family 10
[4194096.219809] lo: Disabled Privacy Extensions
[4194100.359455] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[4194106.403397] eth0: no IPv6 routers present